Category Archives: Automotive

How to Change Your Truck Brake Rotors

If you do have a truck then you probably know to hang your truck brake rotors but if your truck has some sort of anti-lock brakes then you are going to need to know how to change your truck brake rotors  but it isn’t something to worry about its easy to do.

WHAT YOU WILL NEED;

  • Rags
  • Cleaning alcohol
  • Wrench
  • Jack
  • Truck brake rotors

Truck Brake Rotors How to Change Your Truck Brake Rotors

    Your first step will be to park your truck in your garage or in an open area which can be safe for you to work as well as being on level and even ground also.  You are going to need to elevate the truck up to start your work so you are going to need your jack at the use to elevate the truck.

    You are going to need to locate your wheel and then loosen your wheel lugs but remember that the truck should remained very supportive, that the jack has to remain in position and steady of course.

    Your second step will be to disassemble each part of the car; only for the parts which are preventing you getting to the rotor itself.  You are going to know which parts you are going to take out so you could reach your truck brake rotor; you might need a wrench to remove some of the parts in the car.

    Your third step will be to remove the rotor; if you have removed all of the cars parts then you should find your rotor.  You will have to remove the brake caliper and other things to get to your rotors however.  Be careful when you are removing all of the parts however because you don’t want to hurt yourself; you don’t want to keep the parts out in the sun or on the ground, you should try to store them in a cool, dry place which won’t get any dirt on them.  Getting dirt on your wheel bearings may lead to contamination and if they do get contaminated then you might have to replace the wheel bearings.

    Your fourth step is going to be cleaning and matting your surface of your car.  You will need to clean your car; get rid of any dirt or dust that has found its way into your car should be vital because you are going to have to think about the parts of the car.  You need your rotor to work properly but it might not if there is a collection of dirt and dust in your car, it is the same with your brakes, if you don’t regularly check and keep the brakes clean then you might find they don’t work as how they should.

    Your fifth step will be to install your new rotor; now to install your new rotor is actually quite easy once you know how to do it.  You just need to take out the old rotor from your car and then replace with the new rotor.  The only problem that you might have is remembering where the other parts go when you are trying to put them back in so even taking down a note or two as to which order and where they go could help you.

    Your sixth steps is going to put everything back to where it was originally; now you are going to have to put your wheel back into its place and then your wheel lugs also.  Remember you have to be sure that your wheel lugs are tight enough so that they don’t fly off when you drive your car; so checking that they are in securely in is best before you test drive your car.

    Your seventh step is to test drive your brakes; you really do want to take your truck out for a test drive so that you can be sure that your brakes are perfectly working but remember try to do this in open country and not on any of the busy roads.

    Your eighth step is going to be your rear truck brake rotor; if you do need to change your rear rotor then you are going to really do the same as the front procedure.  This too is a simple procedure to follow however so you don’t need to get a professional in because you now know how to do it yourself.

    Your ninth step is going to be to make sure of everything that you have done so far, making sure that you have jacked the car up properly and that everything is secure enough when you are placing the old parts.

    Truck Brake Rotors 1 How to Change Your Truck Brake Rotors

    The tenth step will be to look over all of your parts in the truck; you need to make sure that everything is in good working order and that nothing has began to rust.  Checking on the brake pads is a good idea to do just to make sure that you are going to need to change any of the parts.

    The eleventh step you should try will be to test drive your truck; now make sure you have done all of your cleaning first though and have taken out all old part and put the new parts in before you take it out for a drive.  This will be done so that you know that everything is working and in good working order also.

    Your final step isn’t really a step but rather just a good tip to try when it comes to your truck; you should get some alcohol when it comes to cleaning your new rotor, it would be the best thing to do before you install your new rotor.

    How to Remove a Car’s Pinstriping

    Lucky charm does not favor everyone and he/she cannot possess a new scintillating car. A majority of people have to satisfy with used cars. There is possibility that we may come across some fascinating used cars, which are on sale at affordable prices. However, the problem with most of the used cars is that they have stickers, which the users stick as a memorabilia. You have to remove these stickers in order to make the car yours.

    How to Remove a Cars Pinstriping How to Remove a Cars Pinstriping

    Steps to remove a car’s pinstriping

    1. It is the patience, which you require the most while pinstriping the car. You need to have all the necessary things in order to avoid problems in the future. Purchasing a decal car remover from the local car accessory shop may be a good idea. If you do not get it, then there is no need to panic and run to every shop in search, as there are other options available in the market. Get some rags, scrubbing pads and micro fiber cloth in order to continue with the cleaning process. You can finish off the task easily by getting car wax. Get a hair dryer, as this may come handy if you require some priming.
    2. You need to ascertain different methods of pinstriping before finalizing with a method. If you notice that pinstripe is peeling, then you just need a sticker remover bottle and some rags for cleaning the car. However, if the pinstripe does not show any sign of removal, then you need to carry on with further steps.
    3. Initially, you need to heat the pinstripes with hair dryer. You need to avoid getting too close to the paint, as this potentially damages it and increases your expenses.
    4. Spray the pinstripe cleaner at the initial stages and use a plastic scrapper for rubbing edges of pinstripes. Again, you need to take care of the paint, as this can spoil the paint.
    5. You need to rub the pinstripe to the extent that you can remove or peel off the sticker with your hands. If there is need to spray, then use it, otherwise you need to avoid spraying repeatedly, as your car’s paint is at risk.
    6. Wash and wax the area covered with pinstripe, as many times, some remnants stay on the edges of the car. If the paint of the car is old, then you need to go for repaint.

    Tips

    • You may require a spray, scrubber and a wax can for pinstriping your car.

    Warning

    • Avoid overheating of surface, which is going to remain under the sun for the entire day.

    How Hybrid Cars Work

    A hybrid is a type of car which has two types of motors which provide power to the wheels by synchronization. One of the most popular combinations is where the electric motor helps the gasoline engine. This way the gasoline reserves fuel by periodically shutting off.

    There are two usual categories that hybrid cars are subdivided into. One category is where only use of the electric motor, at low speeds, propels the car. When more power is required, the electric motor has the ability to assist the engine. Even while passing on a steep road or climbing, the electric motor helps out the gasoline one. This initial category is where the Ford Escape and the Toyota Prius Hybrid fall in.

    how hybrid cars work How Hybrid Cars Work

    The second kind needs more horsepower so that its gas engine can drive in rapid acceleration or while moving up hill. The excess power from the electric motor is utilized to assist the internal combustion engine. The Civic Hybrid and the Honda Insight are great examples of this second category. Some resemblances are seen in these two engines as well.

    When the gasoline engine is assisted by the electric motor, both motors deplete power from the battery which gets simultaneously self-recharged from the gasoline engine. For this reason, a hybrid car doesn’t need to get plugged into a source of power to recharge the battery. In hybrid cars, this is the most important aspect.

    Sealed nickel metal hydride batteries are usually utilized by hybrid cars. They are a technology largely used in the cell phones and laptops. Easy to make and cost effective, these batteries are more long lasting, making them ideal for higher valued cars.

    More and more often, hybrid engineers have opted for unconventional designs that maximize the aerodynamics inside the engine. This is the reason for the slim structure. The sleek configuration makes the car almost slippery, giving the cars an original, ultra low drag coefficient. Since a vehicle requires less fuel to move as well as less power when it has less drag, carmakers strive to reduce this drag.

    An on board computer system monitors the electrical system. When the vehicle coasts downhill and the breaks are applied, the system’s polarity is automatically reversed and the motor actually turns into a unit that generates energy. When the conversion of mechanical energy to electrical energy stores power into the battery, this is called regenerative.

    In order to conserve the fuel reserve of the gasoline engine, most hybrid cars will shut it off during road signals. This is a phenomenon called idle stop characteristics. Other than emission reduction and fuel saving, electrical consumption is cut down during idle conditions. Getting assistance from the electric motor, the gasoline engine resumes work upon pressing the accelerator paddle. During this time the loss or delay in performance is silent and seamless and almost negligible.

    Shot peeing is the term given to the special forging by which hybrid cars are manufactured. It increases efficiency and reduces friction in the sidewalls of the cylinder.

    Easily termed as the next generation of cars, hybrids offer marginal and exceptional gas emissions, and an air of extraordinary technological advancement.

    How to Build a Trailer

    Some of us would like the idea of building our own trailer and we all know how difficult it is. With some simple tips I have, we can assemble our own trailer putting up in a small amount of money that is if you’re willing to pull all your stuff.

    Materials You’ll Need

    • A base trailer
    • Power drill
    • 16pcs of L Brackets
    • A 2×4 plywood
    • Some wirings
    • Lights of a trailer

    how to build a trailer How to Build a Trailer

    How to Build a Trailer

    1. You need all those materials and make sure to have them laid out so you’ll know that you have all you needed. Check all the measurements of all wood pieces and be sure that all of the sizes are fit together. Mainly, you may have to measure its length of a trailer you want and measure the width as well. Keep in mind, that you are only making a simple trailer with a wide open top.
    2. Start putting those pieces together. Then you need to have the plywood ready as your baseboards. You need a bolt to its metal parts which is to be connected unto to your base trailer. For your width-wise trailer, you may need some metal rods, this will serve as the support for your baseboards. So when you install it, it will be very easy for you to attach it. When they are all bolted together, then its easy for you to proceed to the next procedure.
    3. Then you can now add the sides of your trailer by using the screwdriver so that it will be easy for you hold on to its side boards. Use the L brackets so that it will connect the end of your sidewalls and your baseboard. It will avoid from falling off and it will add security to the trailer. When your making a basic trailer all you need is just 5inches for the side boards.
    4. Then you may need to connect together all the walls of your trailer by using the L brackets. And just the same connect them on each end to one of the sideboards. So it will secure the baseboards to as well as to the board.
      Check if the sides are all tight and good. Once its been put together, be sure that it is all tight so that things won’t be ruin and won’t fall out. In a few months time, you may have to make sure that you tighten them together but think again its inexpensive and a lot more cheaper than buying a new one.
    5. Lastly, you can now add the lights inside its the last thing that you need to do. Its so easy, just attach the lights on the back of your trailer so that people can see it. Then attach the wire to the generic wiring and you may then plug it right into your trailer light hook it up when you are going to use them. Just easy as 1-2-3. And one tip is to make sure you have enough space for your trailer to pull and turn on the cords out of the harness or else you will be stuck.

    How to Buy a Motorcycle

    Buying a motorcycle can be an exciting thing to do, but this only happens when you know how to choose the right one. There are many things you will have to consider before selecting one, the best way to do this  in the first place, is to keep in mind why you need the motorcycle. Whether you go for a new or used motorcycle is your choice, but just like many other items, there are factors you will use to select the right motorcycle.

    Use of the motorcycle

    How you intend to use the motorcycle will determine the type you go for since the various types are meant for different purposes. You have a wide selection of motorcycles to choose from and these include the standard bikes, touring bikes, cruisers, sport bikes, dual-purpose and motocross bikes. Your needs will tell you which one is right to buy.

    Motorcycle How to Buy a Motorcycle

    Riding experience

    When you want to buy a motorcycle, you should also consider your level of experience in riding. This is because you need to get a motorcycle that you can handle, for instance, you can’t go for a heavy or very fast motorcycle when you are just an inexperienced rider. There are motorcycles types that are good for people like you, like the standard motorcycles. Motorcycles come with different power capabilities which are measured in cc and you can choose this according to how good you are.

    Cost of the motorcycle

    It is always good to compare the price with what you will be getting in terms of the features of the motorcycle. Once you have decided on the type of motorcycle you want, you can now set out to look for a place you can get something of quality and at a price you can afford. Apart from the price of buying it, other costs involved include state registration fee, license plate fee, title fee and insurance.

    Where to buy

    You can buy a motorcycle from a private seller or dealer, your choice will be dependent on several things.

    • Financing. When you get it from a dealer, you may benefit from several buying options in which case you may pay cash or through monthly payments. With a private seller, you will need to pay cash for it.
    • Price. When you buy it from a dealer, it might be a bit  expensive especially when you make monthly payments due to the interest rates.

    Body type of motorcycle

    Motorcycles come with different weight and height features hence when you are buying one make sure you are going to be comfortable riding on it. A test drive would help to determine whether the motorcycle is too high or too low for you. If you are having difficulty getting onto the motorcycle, then it might just be too tall for you.

    Checking out the motorcycle

    When you find the right motorcycle you want to buy, you can test it out to ensure everything is in good working condition especially if it is a used motorcycle. Some of the things to check are the handle bars, levers and pedals, forks, suspension, exhaust frames and the electrics. You can also have a test ride which will help you identify anything bad with the motorcycle that you may not desire.

    Powered by WordPress | Maintained by: Expert How | Thanks to Mega HowTo